Products – The Switch Masters https://theswitchmasters.com Rocker, Push & Custom Switches Fri, 19 Apr 2024 18:37:58 +0000 en hourly 1 https://wordpress.org/?v=6.5.4 Momentary Rocker Switch Winch IN-OUT Symbol https://theswitchmasters.com/product/momentary-rocker-switch-winch-in-out-symbol/ Mon, 04 Apr 2022 14:49:00 +0000 https://theswitchmasters.com/?post_type=product&p=91329 Momentary Rocker Switch Winch IN-OUT Symbol is a double throw momentary switch (returns to center position by the spring) designed to operate your 12 volt 4WD Winch.]]> Momentary Rocker Switch Winch IN-OUT Symbol is a double throw momentary switch (returns to center position by the spring) designed to operate your 12 volt 4WD Winch. it has a face surface size of 2″ x 1″ (50mm x 25mm) and uses a standard din size mounting hole of .86″ x 1.46″ (22mm x 37mm). this is the standard size of most switch holes in modern vehicles, however it is best to check your particular hole size if unsure.

All symbols are laser etched directly onto the switch face to ensure long image life. We do not use stickers or ink which will wear off in a very short time.

FEATURES:

• Double Pole Double Throw MOMENTARY switch
• Black hard surface rocker
• Twin upper and Single lower incandescent lights
• Upper lights are ON when the switch is pressed UP
• Lower light is ON when switch is pressed DOWN
• Same size as the Carling and ARB switches
• Rated 20A 12V
• No rear barriers between terminals
• Wiring diagram supplied with switch

Momentary Rocker Switch Winch IN-OUT Symbol is a product of The Switch Masters

]]> 2 Push Switch Panel for Toyota Tacoma 2016-2022 https://theswitchmasters.com/product/2-push-switch-panel-for-toyota-tacoma-2016-2022/ Wed, 30 Mar 2022 13:09:00 +0000 https://theswitchmasters.com/?post_type=product&p=91238 *. The panel mounts to the existing cubby hole opening to the left of the steering wheel on the 2016-2022 Toyota Tacoma.

 

]]> 2 Push Switch Panel for Toyota Tacoma 2016-2022 allows you to run up to 2 OEM style switches*. The panel mounts to the existing cubby hole opening to the left of the steering wheel on the 2016-2022 Toyota Tacoma (use OEM screws that hold cubby hole to the vehicle). This panel is made out of heavy duty ABS Plastic for years of service, will not rust like the competition.

*Switches are not included.

This plate is as easy as 3 steps to get you an additional 2 TOYOTA PUSH SWICTHES.

Step 1: Pop out the trim by simply using a pry tool to get the clips off, the entire front plate will come out.

Step 2: Remove four corner screws that are holding the cubby to the front cover.

Step 3: Align the Push Switch Panel for Toyota Tacoma 2016-2020, using the same screws you removed from the cubby attached to the front cover.

FEATURES:

• Made out of lightweight, durable long lasting ABS Plastic
• Provide a clean and organized place to add OEM push switches
• No cutting or drilling required
• Will not rust or bend like the competition
• No additional parts need it for install (use OEM screws)
• TOYOTA PUSH SWITCHES NOT INCLUDED

2 Push Switch Panel for Toyota Tacoma 2016-2022 is a product of The Switch Masters

]]> Daisy Chain Harness for Toyota “Push Style” Switches (Large & Small) https://theswitchmasters.com/product/daisy-chain-harness-for-toyota-push-style-switches/ Tue, 15 Mar 2022 13:42:00 +0000 https://theswitchmasters.com/?post_type=product&p=91021 Daisy Chain Harness for Toyota “Push Style” Switches (Large & Small) allows you to expand the illumination to an additional switch or switches, you can add up to 6 daisy chain that will securely give you illumination for up to 7 switches, which is the maximum amount of switches supported by the system.

 

NOTE: The Daisy Chain Harness does not work on the DUAL PUSH SWITCH for Toyota (Large & Small)

 

How does it work?

Simply plug the Daisy Chain Harness into the intended connector, attach the green connector to your new switch, and finish the install by wiring the remaining 2 wires following the switch wiring diagram (out to the accessory relay & to a 12V source)

 

 

Package Included:

  • 1 x Daisy Chain Harness

 

Daisy Chain Harness for Toyota “Push Style” Switches (Large & Small) is a The Switch Masters product

]]> Quick Charge 3.0 Dual USB Power Socket for Toyota https://theswitchmasters.com/product/quick-charge-3-0-dual-usb-power-socket-for-toyota/ Tue, 15 Mar 2022 13:12:00 +0000 https://theswitchmasters.com/?post_type=product&p=91016 Quick Charge 3.0 Dual USB Power Socket for Toyota allows you to charge any device including digital cameras, PDAs, mobile phones and USB accessories.

 

]]> Quick Charge 3.0 Dual USB Power Socket for Toyota allows you to charge any device including digital cameras, PDAs, mobile phones and USB accessories. This socket fits on all late model Toyotas SUV’s and some cars, it will give you the charging convenience no matter where you travel. With short circuit protection, the Quick Charge 3.0 Dual USB Power Socket is the ideal solution for those who are always on the go. It never overheats and has a dual socket so you can charge two devices at one time. Make keeping your device ready for use simple by using this Socket. It will ensure that you stay connected when you need to the most.

What is a QC 3.0 car charger?

Quick Charge 3.0 is engineered to refuel devices up to four times faster than conventional charging. It is designed to charge twice as fast as Quick Charge 1.0 and to be 38 percent more efficient than Quick Charge 2.0. Now consumers can spend even less time charging, and can grab and go more quickly.

FEATURES:

• The product is manufactured to fit in the OEM space available in your car or truck, simple to install
• Dual USB ports, can charge two different devices simultaneously
• Intelligent Charging – Dual Quick Charge USB Port, built-in smart charging IC, will auto detects your devices and charges them at optimal speed, better charging performance; QC 3.0 Backward-compatible with QC 2.0, 1.0, provides standard charging for non-Quick Charge devices
• Safety Protection Function – Built-in safety fuse, with overheat protection. When overcharged, charging will be stopped, it will recover after cooling, and it is safer to use
• Material: ABS + Electronic components
• Input voltage: DC 12-24V
• Output voltage: DC 5V 3A / 9V 2A / 12V 1.5A

KIT CONTAINS:

• 1 USB Dual power socket
• 1 Connector with cable for easy installation

FITS THESE VEHICLES:

• Toyota Tacoma 2005-2011
• Toyota Tacoma 2012-2015 (Left Side ONLY)
• Toyota Tacoma 2016 – 2020 (Left Side ONLY)
• Toyota FJ Cruiser 2007-2014
• Toyota Fortuner 2005-2014
• Toyota Hilux 2005-2014
• Toyota Highlander 2001-2007
• Toyota Tundra 2005-2006 (Center Console if equipped)
• Toyota 4Runner 2003-2009
• Toyota Prado 120 Series 2003-2009
• Toyota Land Cruiser 100 Series 1998-2007
• Toyota Land Cruiser 75, 76, 78 & 79 series

Quick Charge 3.0 Dual USB Power Socket for Toyota is a The Switch Masters product

]]> Quick Charge 3.0 Small Dual USB Power Socket for Toyota https://theswitchmasters.com/product/quick-charge-3-0-small-dual-usb-power-socket-for-toyota/ Tue, 15 Mar 2022 12:19:00 +0000 https://theswitchmasters.com/?post_type=product&p=91005 Quick Charge 3.0 Small Dual USB Power Socket for Toyota allows you to charge any device including digital cameras, PDAs, mobile phones and USB accessories.

 

]]> Quick Charge 3.0 Small Dual USB Power Socket for Toyota allows you to charge any device including digital cameras, PDAs, mobile phones and USB accessories. This socket fits on all late model Toyotas SUV’s and some cars, it will give you the charging convenience no matter where you travel. With short circuit protection, the Quick Charge 3.0 Small Dual USB Power Socket is the ideal solution for those who are always on the go. It never overheats and has a dual socket so you can charge two devices at one time. Make keeping your device ready for use simple by using this Socket. It will ensure that you stay connected when you need to the most.

What is a QC 3.0 car charger?

Quick Charge 3.0 is engineered to refuel devices up to four times faster than conventional charging. It is designed to charge twice as fast as Quick Charge 1.0 and to be 38 percent more efficient than Quick Charge 2.0. Now consumers can spend even less time charging, and can grab and go more quickly.

FEATURES:

• The product is manufactured to fit in the OEM space available in your car or truck, simple to install
• Dual USB ports, can charge two different devices simultaneously
• Intelligent Charging – Dual Quick Charge USB Port, built-in smart charging IC, will auto detects your devices and charges them at optimal speed, better charging performance; QC 3.0 Backward-compatible with QC 2.0, 1.0, provides standard charging for non-Quick Charge devices
• Safety Protection Function – Built-in safety fuse, with overheat protection. When overcharged, charging will be stopped, it will recover after cooling, and it is safer to use
• Material: ABS + Electronic components
• Input voltage: DC 12-24V
• Output voltage: DC 5V 3A / 9V 2A / 12V 1.5A

KIT CONTAINS:

• 1 USB Dual power socket
• 1 Connector with cable for easy installation

FITS THESE VEHICLES:

• Toyota Tacoma 2012-ON (Center Console ONLY)
• Toyota Tundra 2008-2021
• Toyota 4Runner 2010-ON
• Toyota Land Cruiser Prado 150 Series 2010-2014
• Toyota Land Cruiser 200 Series 2008-2013
• Toyota Sequoia 2008-ON
• Toyota Corolla 2006-2013
• Toyota Highlander 2008-ON
• Toyota RAV4 2008-2012
• Toyota Yaris 2008
• Toyota Camry 2011-2014

Quick Charge 3.0 Small Dual USB Power Socket for Toyota is a The Switch Masters product

]]> Small Push Switch for Toyota – Rock Lights Symbol https://theswitchmasters.com/product/small-push-switch-for-toyota-rock-lights-symbol-5/ Thu, 10 Mar 2022 11:31:00 +0000 https://theswitchmasters.com/?post_type=product&p=90951 Small Push Switch for Toyota – Rock Lights Symbol is a High Quality 12 Volt Push Switch. This switch allows you to operate any 12 volt accessories, this fits on all late model Toyotas SUV’s and some other model cars. Toyota Small Push Switch Rear Camera Symbol 3

 

]]> Small Push Switch for Toyota – Rock Lights Symbol allows you to operate any 12 volt accessories, with short circuit protection, the Industries High Quality 12 volt Push Switch will give you a clean and original style look, they are install in the existing holes that come with the vehicle and it has a face surface size of 1.28″ x 0.87″ (32.5 mm x 22 mm).

This switches are made out of heavy duty ABS plastic that will ensure years of service and come in a mate black surface color, the same color as the OEM Switches, All symbols are Laser etched directly onto the switch face using modern high Tech laser engraving equipment to ensure long image life. 

These Switches are an aftermarket switch that locks into your existing panel super easy to install in less than 10 min’s.

FEATURES:

• The product is manufactured to fit in the OEM space available in your car or truck, simple to install
• Single Pole Single Throw ON-OFF Small Push switch
• Black hard surface rocker
• Laser etched Legend
• Single upper L.E.D light
• Single lower L.E.D light
• Upper light is ON when the switch is pressed IN
• Lower light can be wired to separate dash light circuit
• Rated at 3 Amp 12V
• Wiring diagram supplied with switch

The switch is an electronic switch rated at 3 amp’s. Therefore in ALL cases the accessory MUST be wired through a fused relay.

KIT CONTAINS:

• 1 Toyota Small Push Switch
• 1 Connector with cable for easy installation

FITS THESE VEHICLES:

• Toyota Tacoma 2012-ON (Center Console ONLY)
• Toyota Tundra 2008-ON
• Toyota 4Runner 2010-ON
• Toyota Land Cruiser Prado 150 Series 2010-2014
• Toyota Land Cruiser 200 Series 2008-2013
• Toyota Sequoia 2008-ON
• Toyota Corolla 2006-2013
• Toyota Highlander 2008-ON
• Toyota RAV4 2008-2012
• Toyota Yaris 2008
• Toyota Camry 2011-2014

Small Push Switch for Toyota – Rock Lights Symbol is a The Switch Masters product

]]> Small Push Switch for Toyota – Rock Lights Symbol https://theswitchmasters.com/product/small-push-switch-for-toyota-rock-lights-symbol/ Thu, 10 Mar 2022 11:29:00 +0000 https://theswitchmasters.com/?post_type=product&p=90945 Small Push Switch for Toyota – Rock Lights Symbol is a High Quality 12 Volt Push Switch. This switch allows you to operate any 12 volt accessories, this fits on all late model Toyotas SUV’s and some other model cars. Toyota Small Push Switch Rear Camera Symbol 3

 

]]> Small Push Switch for Toyota – Rock Lights Symbol allows you to operate any 12 volt accessories, with short circuit protection, the Industries High Quality 12 volt Push Switch will give you a clean and original style look, they are install in the existing holes that come with the vehicle and it has a face surface size of 1.28″ x 0.87″ (32.5 mm x 22 mm).

This switches are made out of heavy duty ABS plastic that will ensure years of service and come in a mate black surface color, the same color as the OEM Switches, All symbols are Laser etched directly onto the switch face using modern high Tech laser engraving equipment to ensure long image life. 

These Switches are an aftermarket switch that locks into your existing panel super easy to install in less than 10 min’s.

FEATURES:

• The product is manufactured to fit in the OEM space available in your car or truck, simple to install
• Single Pole Single Throw ON-OFF Small Push switch
• Black hard surface rocker
• Laser etched Legend
• Single upper L.E.D light
• Single lower L.E.D light
• Upper light is ON when the switch is pressed IN
• Lower light can be wired to separate dash light circuit
• Rated at 3 Amp 12V
• Wiring diagram supplied with switch

The switch is an electronic switch rated at 3 amp’s. Therefore in ALL cases the accessory MUST be wired through a fused relay.

KIT CONTAINS:

• 1 Toyota Small Push Switch
• 1 Connector with cable for easy installation

FITS THESE VEHICLES:

• Toyota Tacoma 2012-ON (Center Console ONLY)
• Toyota Tundra 2008-ON
• Toyota 4Runner 2010-ON
• Toyota Land Cruiser Prado 150 Series 2010-2014
• Toyota Land Cruiser 200 Series 2008-2013
• Toyota Sequoia 2008-ON
• Toyota Corolla 2006-2013
• Toyota Highlander 2008-ON
• Toyota RAV4 2008-2012
• Toyota Yaris 2008
• Toyota Camry 2011-2014

Small Push Switch for Toyota – Rock Lights Symbol is a The Switch Masters product

]]> Small Push Switch for Toyota – Winch Power Symbol https://theswitchmasters.com/product/small-push-switch-for-toyota-winch-power-symbol-2/ Thu, 10 Mar 2022 11:28:00 +0000 https://theswitchmasters.com/?post_type=product&p=90939 Small Push Switch for Toyota – Winch Power Symbol is a High Quality 12 Volt Push Switch. This switch allows you to operate any 12 volt accessories, this fits on all late model Toyotas SUV’s and some other model cars. Toyota Small Push Switch Rear Camera Symbol 3

 

]]> Small Push Switch for Toyota – Winch Power Symbol allows you to operate any 12 volt accessories, with short circuit protection, the Industries High Quality 12 volt Push Switch will give you a clean and original style look, they are install in the existing holes that come with the vehicle and it has a face surface size of 1.28″ x 0.87″ (32.5 mm x 22 mm).

This switches are made out of heavy duty ABS plastic that will ensure years of service and come in a mate black surface color, the same color as the OEM Switches, All symbols are Laser etched directly onto the switch face using modern high Tech laser engraving equipment to ensure long image life. 

These Switches are an aftermarket switch that locks into your existing panel super easy to install in less than 10 min’s.

FEATURES:

• The product is manufactured to fit in the OEM space available in your car or truck, simple to install
• Single Pole Single Throw ON-OFF Small Push switch
• Black hard surface rocker
• Laser etched Legend
• Single upper L.E.D light
• Single lower L.E.D light
• Upper light is ON when the switch is pressed IN
• Lower light can be wired to separate dash light circuit
• Rated at 3 Amp 12V
• Wiring diagram supplied with switch

The switch is an electronic switch rated at 3 amp’s. Therefore in ALL cases the accessory MUST be wired through a fused relay.

KIT CONTAINS:

• 1 Toyota Small Push Switch
• 1 Connector with cable for easy installation

FITS THESE VEHICLES:

• Toyota Tacoma 2012-ON (Center Console ONLY)
• Toyota Tundra 2008-ON
• Toyota 4Runner 2010-ON
• Toyota Land Cruiser Prado 150 Series 2010-2014
• Toyota Land Cruiser 200 Series 2008-2013
• Toyota Sequoia 2008-ON
• Toyota Corolla 2006-2013
• Toyota Highlander 2008-ON
• Toyota RAV4 2008-2012
• Toyota Yaris 2008
• Toyota Camry 2011-2014

Small Push Switch for Toyota – Winch Power Symbol is a The Switch Masters product

]]> Small Push Switch for Toyota – Air Compressor Symbol https://theswitchmasters.com/product/small-push-switch-for-toyota-air-compressor-symbol-4/ Thu, 10 Mar 2022 11:22:00 +0000 https://theswitchmasters.com/?post_type=product&p=90933 Small Push Switch for Toyota – Air Compressor Symbol is a High Quality 12 Volt Push Switch. This switch allows you to operate any 12 volt accessories, this fits on all late model Toyotas SUV’s and some other model cars. Toyota Small Push Switch Rear Camera Symbol 3

 

]]> Small Push Switch for Toyota – Air Compressor Symbol allows you to operate any 12 volt accessories, with short circuit protection, the Industries High Quality 12 volt Push Switch will give you a clean and original style look, they are install in the existing holes that come with the vehicle and it has a face surface size of 1.28″ x 0.87″ (32.5 mm x 22 mm).

This switches are made out of heavy duty ABS plastic that will ensure years of service and come in a mate black surface color, the same color as the OEM Switches, All symbols are Laser etched directly onto the switch face using modern high Tech laser engraving equipment to ensure long image life. 

These Switches are an aftermarket switch that locks into your existing panel super easy to install in less than 10 min’s.

FEATURES:

• The product is manufactured to fit in the OEM space available in your car or truck, simple to install
• Single Pole Single Throw ON-OFF Small Push switch
• Black hard surface rocker
• Laser etched Legend
• Single upper L.E.D light
• Single lower L.E.D light
• Upper light is ON when the switch is pressed IN
• Lower light can be wired to separate dash light circuit
• Rated at 3 Amp 12V
• Wiring diagram supplied with switch

The switch is an electronic switch rated at 3 amp’s. Therefore in ALL cases the accessory MUST be wired through a fused relay.

KIT CONTAINS:

• 1 Toyota Small Push Switch
• 1 Connector with cable for easy installation

FITS THESE VEHICLES:

• Toyota Tacoma 2012-ON (Center Console ONLY)
• Toyota Tundra 2008-ON
• Toyota 4Runner 2010-ON
• Toyota Land Cruiser Prado 150 Series 2010-2014
• Toyota Land Cruiser 200 Series 2008-2013
• Toyota Sequoia 2008-ON
• Toyota Corolla 2006-2013
• Toyota Highlander 2008-ON
• Toyota RAV4 2008-2012
• Toyota Yaris 2008
• Toyota Camry 2011-2014

Small Push Switch for Toyota – Air Compressor Symbol is a The Switch Masters product

]]> Momentary Small Push Switch for Toyota – Horn Symbol https://theswitchmasters.com/product/momentary-small-push-switch-for-toyota-horn-symbol-2/ Thu, 10 Mar 2022 11:19:00 +0000 https://theswitchmasters.com/?post_type=product&p=90922 Momentary Small Push Switch for Toyota – Horn Symbol allows you to operate any 12 volt accessories, with short circuit protection, the Industries High Quality 12 volt Push Switch will give you a clean and original style look. Warning]]> Momentary Small Push Switch for Toyota – Horn Symbol allows you to operate any 12 volt accessories, with short circuit protection, the Industries High Quality 12 volt Push Switch will give you a clean and original style look, they are install in the existing holes that come with the vehicle and it has a face surface size of 1.28″ x 0.87″ (32.5 mm x 22 mm).

This switches are made out of heavy duty ABS plastic that will ensure years of service and come in a mate black surface color, the same color as the OEM Switches, All symbols are Laser etched directly onto the switch face using modern high Tech laser engraving equipment to ensure long image life. 

FEATURES:

• The product is manufactured to fit in the OEM space available in your car or truck, simple to install
• Single Pole Single Throw MOMENTARY Push switch
• Black hard surface rocker
• Laser etched Legend
• Single upper L.E.D light
• Single lower L.E.D light
• Upper light is ON when the switch is pressed IN
• Lower light can be wired to separate dash light circuit
• Rated at 3 Amp 12V
• Wiring diagram supplied with switch

The switch is an electronic switch rated at 3 amp’s. Therefore in ALL cases the accessory MUST be wired through a fused relay.

KIT CONTAINS:

• 1 Toyota MOMENTARY Small Push Switch
• 1 Connector with cable for easy installation

FITS THESE VEHICLES:

• Toyota Tacoma 2012-ON (Center Console ONLY)
• Toyota Tundra 2007-ON
• Toyota 4Runner 2010-ON
• Toyota Land Cruiser Prado 150 Series 2010-2014
• Toyota Land Cruiser 200 Series 2008-2013
• Toyota Sequoia 2008-ON
• Toyota Corolla 2006-2013
• Toyota Highlander 2008-ON
• Toyota RAV4 2008-2012
• Toyota Yaris 2008
• Toyota Camry 2011-2014

Momentary Small Push Switch for Toyota – Horn Symbol is a Part of The Switch Masters

]]>